Alexan

ACE 6344-47 One Relay Module Delayed Power Off, Disconnected, Trigger Delay, Cycle Timing Circuit Switch

ACE 6344-47 One Relay Module Delayed Power Off, Disconnected, Trigger Delay, Cycle Timing Circuit Switch

Product details of 6-30V Micro USB Digital LCD Display Time Delay Relay Module Control Timer Switch Trigger Cycle
Timing Range:0.01 sec~9999 min

This product lcd display, very clear, simple and easy to use, powerful, but please read user instructions carefully before using.

  • Product Highlights:
  • 1. Display with LCD two columns, Can display parameters directly;
  • 2. Trigger mode: high and low level, switch quantity, meet most of the needs.
  • 3. Power supply: 6~30V, also supports micro USB 5.0V, very convenient.  Anti back connection of power supply.
  • 4. Parameters can be modified via UART.
  • 5. Stop button to provide emergency stop function.
  • 6. 5 minutes without any operation into a low-power state. Any action wake up.
  • 7. OP/CL/LOP params can be modified individually
  • 8. All parameters are automatically saved by power off.
  • Working Mode Introduction(P1~P7)
  • P1: After the signal is triggered, the relay conduction in OPtime then disconnects; In the OPtime, the signal is invalid.
  • P2: After the signal is triggered, the relay conduction in OPtime then disconnects; In the OPtime, the signal triggers a new timer.
  • P3: After the signal is triggered, the relay conduction inOPtime then disconnects; In theOPtime, signal trigger reset timer,relay disconnected and stop timing.
  • P4: When triggered, After the relay is disconnected fromCLtime, relay conductionOPtime, after timing is complete, disconnect relay.
  • P5: When triggered, After the relay conduction op time, the relay disconnects the CL time, and then loops the above action, gives the signal again in the loop, relays disconnect, stops the timer, and the number of cycles (LOP) can be set;
  • P6: When triggered, After the relay conduction op time, the relay disconnects the CL time, and then loops the above action, signal is invalid in the loop, the number of cycles (LOP) can be set;
  • P7: Signal hold function: The signal is maintained, the timing is cleared, and the relay conduction; when the signal disappears, the relay disconnects after the timing OP; during the timing, there is another signal and the timing is cleared
  • Additional features:
  • a) Low-power state: In the running interface, by pressing the STOP button for a long time, the Low-power function is started or closed (L-P selects on to start the hibernation function, and off turns off the hibernation function);
  • b) Relay function selection: In the operation interface, by pressing the STOP button shortly, the relay function is started or closed, ‘on’ meets the conduction condition relay normally turns on, ‘OFF’ meets the conduction condition relay does not turn on; ‘OFF’ In the state, the system flashes ‘OUT’;
  • c) Parameter view: In the operation interface, short press the SET key to display the current parameter setting of the system, without affecting the normal operation of the system;
  • d) Display content switching: In P-5 P-6 mode, switch display content (run time/cycle number) by pressing DOWN key momentarily

 

SKU: ACE6344-47 Category: Tag:

ACE 6344-47 One Relay Module Delayed Power Off, Disconnected, Trigger Delay, Cycle Timing Circuit Switch

  • Product Parameters:
  • 1. Power Supply: 6V~30V and micro USB 5.0 V
  • 2. Trigger signal source: High level(3.0V~24.0V),Low level(0.0V ~0.2V),Switch signal.
  • 3. Maximum Output load: DC 30V 5A and AC 220V 5A.
  • 4. Static Current: 15mA Operating current: 50mA.
  • 5. Service life: more than 100,000 times; working temperature: -40-85°C; size: 8.0*3.8*1.9cm.
  • 6. Optocoupler isolation, Strong anti-interference ability, Industrial grade circuit board
  • Timing Range:
  • 0.01 sec~9999 min